drivers: Replace deprecated Pin.high()/low() methods with .__call__(1/0).

drivers/display/ssd1306.py

@@ -139,23 +139,23 @@ class SSD1306_SPI(SSD1306):
 
     def write_cmd(self, cmd):
         self.spi.init(baudrate=self.rate, polarity=0, phase=0)
-        self.cs.high()
-        self.dc.low()
-        self.cs.low()
+        self.cs(1)
+        self.dc(0)
+        self.cs(0)
         self.spi.write(bytearray([cmd]))
-        self.cs.high()
+        self.cs(1)
 
     def write_data(self, buf):
         self.spi.init(baudrate=self.rate, polarity=0, phase=0)
-        self.cs.high()
-        self.dc.high()
-        self.cs.low()
+        self.cs(1)
+        self.dc(1)
+        self.cs(0)
         self.spi.write(buf)
-        self.cs.high()
+        self.cs(1)
 
     def poweron(self):
-        self.res.high()
+        self.res(1)
         time.sleep_ms(1)
-        self.res.low()
+        self.res(0)
         time.sleep_ms(10)
-        self.res.high()
+        self.res(1)

drivers/nrf24l01/nrf24l01.py

@@ -66,8 +66,8 @@ class NRF24L01:
         ce.init(ce.OUT, value=0)
 
         # reset everything
-        self.ce.low()
-        self.cs.high()
+        self.ce(0)
+        self.cs(1)
         self.payload_size = payload_size
         self.pipe0_read_addr = None
         utime.sleep_ms(5)
@@ -109,36 +109,36 @@ class NRF24L01:
             self.spi.init(master, baudrate=baudrate, polarity=0, phase=0)
 
     def reg_read(self, reg):
-        self.cs.low()
+        self.cs(0)
         self.spi.readinto(self.buf, reg)
         self.spi.readinto(self.buf)
-        self.cs.high()
+        self.cs(1)
         return self.buf[0]
 
     def reg_write_bytes(self, reg, buf):
-        self.cs.low()
+        self.cs(0)
         self.spi.readinto(self.buf, 0x20 | reg)
         self.spi.write(buf)
-        self.cs.high()
+        self.cs(1)
         return self.buf[0]
 
     def reg_write(self, reg, value):
-        self.cs.low()
+        self.cs(0)
         self.spi.readinto(self.buf, 0x20 | reg)
         ret = self.buf[0]
         self.spi.readinto(self.buf, value)
-        self.cs.high()
+        self.cs(1)
         return ret
 
     def flush_rx(self):
-        self.cs.low()
+        self.cs(0)
         self.spi.readinto(self.buf, FLUSH_RX)
-        self.cs.high()
+        self.cs(1)
 
     def flush_tx(self):
-        self.cs.low()
+        self.cs(0)
         self.spi.readinto(self.buf, FLUSH_TX)
-        self.cs.high()
+        self.cs(1)
 
     # power is one of POWER_x defines; speed is one of SPEED_x defines
     def set_power_speed(self, power, speed):
@@ -190,11 +190,11 @@ class NRF24L01:
 
         self.flush_rx()
         self.flush_tx()
-        self.ce.high()
+        self.ce(1)
         utime.sleep_us(130)
 
     def stop_listening(self):
-        self.ce.low()
+        self.ce(0)
         self.flush_tx()
         self.flush_rx()
 
@@ -204,10 +204,10 @@ class NRF24L01:
 
     def recv(self):
         # get the data
-        self.cs.low()
+        self.cs(0)
         self.spi.readinto(self.buf, R_RX_PAYLOAD)
         buf = self.spi.read(self.payload_size)
-        self.cs.high()
+        self.cs(1)
         # clear RX ready flag
         self.reg_write(STATUS, RX_DR)
 
@@ -229,17 +229,17 @@ class NRF24L01:
         self.reg_write(CONFIG, (self.reg_read(CONFIG) | PWR_UP) & ~PRIM_RX)
         utime.sleep_us(150)
         # send the data
-        self.cs.low()
+        self.cs(0)
         self.spi.readinto(self.buf, W_TX_PAYLOAD)
         self.spi.write(buf)
         if len(buf) < self.payload_size:
             self.spi.write(b'\x00' * (self.payload_size - len(buf))) # pad out data
-        self.cs.high()
+        self.cs(1)
 
         # enable the chip so it can send the data
-        self.ce.high()
+        self.ce(1)
         utime.sleep_us(15) # needs to be >10us
-        self.ce.low()
+        self.ce(0)
 
     # returns None if send still in progress, 1 for success, 2 for fail
     def send_done(self):

drivers/onewire/ds18x20.py

@@ -7,11 +7,11 @@ temperature sensors.  It supports multiple devices on the same 1-wire bus.
 The following example assumes the ground of your DS18x20 is connected to
 Y11, vcc is connected to Y9 and the data pin is connected to Y10.
 
->>> from pyb import Pin
+>>> from machine import Pin
 >>> gnd = Pin('Y11', Pin.OUT_PP)
->>> gnd.low()
+>>> gnd.off()
 >>> vcc = Pin('Y9', Pin.OUT_PP)
->>> vcc.high()
+>>> vcc.on()
 
 >>> from ds18x20 import DS18X20
 >>> d = DS18X20(Pin('Y10'))

drivers/sdcard/sdcard.py

@@ -130,7 +130,7 @@ class SDCard:
         raise OSError("timeout waiting for v2 card")
 
     def cmd(self, cmd, arg, crc, final=0, release=True):
-        self.cs.low()
+        self.cs(0)
 
         # create and send the command
         buf = self.cmdbuf
@@ -150,12 +150,12 @@ class SDCard:
                 for j in range(final):
                     self.spi.write(b'\xff')
                 if release:
-                    self.cs.high()
+                    self.cs(1)
                     self.spi.write(b'\xff')
                 return response
 
         # timeout
-        self.cs.high()
+        self.cs(1)
         self.spi.write(b'\xff')
         return -1
 
@@ -164,15 +164,15 @@ class SDCard:
         self.spi.read(1, 0xff) # ignore stuff byte
         for _ in range(_CMD_TIMEOUT):
             if self.spi.read(1, 0xff)[0] == 0xff:
-                self.cs.high()
+                self.cs(1)
                 self.spi.write(b'\xff')
                 return 0    # OK
-        self.cs.high()
+        self.cs(1)
         self.spi.write(b'\xff')
         return 1 # timeout
 
     def readinto(self, buf):
-        self.cs.low()
+        self.cs(0)
 
         # read until start byte (0xff)
         while self.spi.read(1, 0xff)[0] != 0xfe:
@@ -186,11 +186,11 @@ class SDCard:
         self.spi.write(b'\xff')
         self.spi.write(b'\xff')
 
-        self.cs.high()
+        self.cs(1)
         self.spi.write(b'\xff')
 
     def write(self, token, buf):
-        self.cs.low()
+        self.cs(0)
 
         # send: start of block, data, checksum
         self.spi.read(1, token)
@@ -200,7 +200,7 @@ class SDCard:
 
         # check the response
         if (self.spi.read(1, 0xff)[0] & 0x1f) != 0x05:
-            self.cs.high()
+            self.cs(1)
             self.spi.write(b'\xff')
             return
 
@@ -208,18 +208,18 @@ class SDCard:
         while self.spi.read(1, 0xff)[0] == 0:
             pass
 
-        self.cs.high()
+        self.cs(1)
         self.spi.write(b'\xff')
 
     def write_token(self, token):
-        self.cs.low()
+        self.cs(0)
         self.spi.read(1, token)
         self.spi.write(b'\xff')
         # wait for write to finish
         while self.spi.read(1, 0xff)[0] == 0x00:
             pass
 
-        self.cs.high()
+        self.cs(1)
         self.spi.write(b'\xff')
 
     def count(self):