GitLab

This was made optional in CPython 3.11.
Signed-off-by: Amirreza Hamzavi <amirrezahamzavi2000@gmail.com>

This was made optional in CPython 3.11.
Signed-off-by: Amirreza Hamzavi <amirrezahamzavi2000@gmail.com>

This was made optional in CPython 3.11.
Signed-off-by: Amirreza Hamzavi <amirrezahamzavi2000@gmail.com>

Allows mpremote file transfer to work correctly when mpremote is used over
the ST-link USB/UART REPL port.

Fixes issue #8386.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>

This allows UART RX to function while flash erase/writes operations are
under way, preventing lost serial data so long as it fits in the UART RX
buffer.

This enables (among other things) mpremote to successfully copy files to
boards that use a UART REPL.

Enable via the following option placed in `mpconfigboard.mk`:

    MICROPY_HW_ENABLE_ISR_UART_FLASH_FUNCS_IN_RAM = 1
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>

Signed-off-by: Damien George <damien@micropython.org>

Can be enabled by a board by enabling `MICROPY_PY_NETWORK_PPP_LWIP`.
Signed-off-by: Damien George <damien@micropython.org>

This allows enabling lwIP debugging output.  For example, to enable PPP
debugging add the following to `mpconfigboard.h`:

    #define LWIP_DEBUG 1
    #define PPP_DEBUG LWIP_DBG_ON
Signed-off-by: Damien George <damien@micropython.org>

When timeout=0 (non-blocking mode) the UART should still wait for each
character to go out.  Otherwise non-blocking mode with CTS enabled is
useless because it can only write one character at a time.
Signed-off-by: Damien George <damien@micropython.org>

The errcode should be cleared so the caller sees a successful write, even
if it's a short write.
Signed-off-by: Damien George <damien@micropython.org>

Signed-off-by: Damien George <damien@micropython.org>

Can be enabled by a board by enabling `MICROPY_PY_NETWORK_PPP_LWIP`.
Signed-off-by: Damien George <damien@micropython.org>

This commit adds a new `network.PPP` interface which works on any port that
has bare-metal lwIP, eg rp2, stm32, mimxrt.

It has been tested on stm32.  A board needs to enable
`MICROPY_PY_NETWORK_PPP_LWIP` and then it can use it as follows:

    import network

    ppp = network.PPP(uart)
    ppp.connect()

    while not ppp.isconnected():
        pass

    # use `socket` module as usual, etc

    ppp.disconnect()

Usually the application must first configure the cellular/etc UART link to
get it connected and in to PPP mode first (eg ATD*99#), before handing over
control to `network.PPP`.

The PPP interface automatically configures the UART IRQ callback to call
PPP.poll() on incoming data.
Signed-off-by: Damien George <damien@micropython.org>

Signed-off-by: Damien George <damien@micropython.org>

This updates lwIP from STABLE-2_1_3_RELEASE, which was released in November
2021.  The latest STABLE-2_2_0_RELEASE was released in September 2023.
Signed-off-by: Damien George <damien@micropython.org>

These all require hardware connections, so live in a different directory.

Except for the IRQ_BREAK test of ESP32 devices a single UART with loopback
is sufficient.

General:
    SAMD21: Due to the limited flash size only SAMD21 devices with external
    flash support uart.irq().

IRQ_BREAK:
    ESP32 needs different UART devices for creating and sensing a break.
    Lacking a second UART the test is skipped for ESP32S2 and ESP32C3.  RP2
    does not pass the test reliable at 115200 baud, reason to be found.
    Thus the upper limit is set to 57600 Baud.

    Coverage:
        esp32  pass when different UART devices are used.
        rp2    pass up to 57600 baud

IRQ_RX:
    SAMD21: Being a slow device it needs data to be sent byte-by-byte at
    9600 baud, since the IRQ callback is scheduled delayed and then the
    flags do not match any more.  The data matches since it is queued in
    the FIFO resp. ringbuffer.

    CC3200: The test cannot be performed since no calls are accepted in the
    IRQ handler like u.read(). Skipped.

    Coverage:
        cc3200 fail due to major differences in the implementation.
        esp32  pass
        nrf    pass
        renesas-ra pass
        samd   pass see the notes.
        stm32  pass

IRQ_RXIDLE:
    STM32: With PyBoard the IRQ is called several times, but only once with
    the flag IRQ_RXIDLE set.

    Coverage:
        esp32    pass
        mimxrt   pass
        renesas-ra pass
        rp2      pass
        samd     pass for both SAMD21 and SAMD51
        stm32    fail. see notes.
Signed-off-by: Damien George <damien@micropython.org>
Signed-off-by: robert-hh <robert@hammelrath.com>

The test checks whether the message created by the IRQ handler appears
about at the end of the data sent by UART.

Supported MCUs resp. boards:
- RP2040
- Teensy 4.x
- Adafruit ItsyBitsy M0
- Adafruit ItsyBitsy M4
- NRF52 (Arduino Nano Connect 33 BLE)
Signed-off-by: Damien George <damien@micropython.org>

For more ports and trigger options, based on the current state of the code.
Signed-off-by: robert-hh <robert@hammelrath.com>

These docs now match the code in `extmod/machine_uart.c`.  IRQ trigger
support still need to be updated for each port (to be done in a follow-up
commit).
Signed-off-by: Damien George <damien@micropython.org>

The UART.IRQ_IDLE callback is called about two character times after the
last byte, or 1 ms, whichever is larger.  For the irq, timer 0 is used.

machine_timer.c had to be reworked to make it's mechanisms available for
machine_uart.c.

The irq.flags() value is change only at a requested event.  Otherwise keep
the state.
Signed-off-by: robert-hh <robert@hammelrath.com>

Allowing to define the trigger UART.IRQ_RXIDLE as well as UART.IRQ_RX.  The
delay for the IRQ_RXIDLE interrupt is about 3 character times or 1-2 ms,
whichever is larger.

The irq.flags() value is changed only with an expected event.  Do not
change it otherwise.
Signed-off-by: robert-hh <robert@hammelrath.com>

With the softtimer the minimal delay between the end of a message and the
trigger is 2 ms.  For baud rates <= 9600 baud it's three character times.
Tested with baud rates up tp 115200 baud.  The timer used for RXIDLE is
running only during UART receive, saving execution cycles when the timer is
not needed.

The irq.flags() value is changed only with an expected event.  Do not
change it otherwise.
Signed-off-by: robert-hh <robert@hammelrath.com>

Just adding the event symbol.  No code change required, and no impact on
code execution time when the event is not selected.

Tested with STM32F4xx, STM32F7xx and STM32H7xx.
Signed-off-by: robert-hh <robert@hammelrath.com>

Supported triggers: UART.IRQ_RX and UART.IRQ_TXIDLE.  It will probably work
on other boards as well, but so far untested.

The irq.flags() value is changed only when requested by a triggered event.
Do not change it otherwise.
Signed-off-by: robert-hh <robert@hammelrath.com>

This commit fixes a bug in the existing driver, that the UART baud rate
could not be changed without reset or power cycle.  It adds as well
functionality to UART.deinit().
Signed-off-by: robert-hh <robert@hammelrath.com>

Supported trigger events: IRQ_RX and IRQ_BREAK.  Hard IRQ is not supported.
Signed-off-by: robert-hh <robert@hammelrath.com>

As alternative to RX_ANY to match the names used by the other ports.
Signed-off-by: robert-hh <robert@hammelrath.com>

The renesas-ra port supports calling a handler to be called on every byte
received by UART.  For consistency with other ports, the symbol IRQ_RX
is added as the trigger name.

Side change: Add the received UART data to the REPL input buffer only if it
is the REPL UART.  Otherwise, every UART would act as REPL input.
Signed-off-by: robert-hh <robert@hammelrath.com>

Supported triggers are: IRQ_RXIDLE and IRQ_TXIDLE.

When IRQ_RXIDLE is set, the handler will be called 3 character times after
the data in burst stopped.

When IRQ_TXIDLE is set, the handler will be called immediately after the
data has been sent.

This commit requires a change to fsl_lpuart.c, because the existing code
does not support under-run appropriately.

The irq.flags() value is cleared only at an expected event.  Do not change
it otherwise.
Signed-off-by: robert-hh <robert@hammelrath.com>

Supported for all SAMD51 devices and SAMD21 with external flash.  For
interrupt events, IRQ_RX and IRQ_TXIDLE are provided.

IRQ_RX is called for every received byte.  This may not be useful for high
data rates, but can be used to build a wrapper class providing an
IRQ_RXIDLE event or to signal just the first byte of a message.

IRQ_TXIDLE is called only when messages are longer than 5 bytes and
triggers when still 5 bytes are due to be sent.

The SAMD hardware does not support implementing IRQ_RXIDLE.
Signed-off-by: robert-hh <robert@hammelrath.com>

Supported trigger names: IRQ_RXIDLE, IRQ_TXIDLE, IRQ_BREAK

- IRQ_RXIDLE: The handler for IRQ_RXIDLE is called reliably 31 UART bit
  times after the last incoming data.

- IRQ_TXIDLE: This IRQ is triggered after at least >5 characters are sent
  at once.  It is triggered when the TX FIFO falls below 4 elements.  At
  that time, up to 5 bytes may still be in the FIFO and output shift
  register.

- IRQ_BREAK: The IRQ triggers if a BREAK state is detected at RX.
  Properties & side effects:
  - After a BREAK, a valid character must be received before another break
    can be detected.
  - Each break puts a 0xff character into the input buffer.

The irq.flags() value is cleared only with a new wanted event.  Do not
change the flags otherwise.
Signed-off-by: robert-hh <robert@hammelrath.com>

Not just the domain name.  This gives better HTTP 1.0 examples if someone
wants to copy them.
Signed-off-by: Damien George <damien@micropython.org>

`ssl.wrap_socket()` is deprecated in CPython, so use `SSLContext` instead,
so the example is a good example to copy.
Signed-off-by: Damien George <damien@micropython.org>

The main changes here are to pass the address family and socket type to
`getaddrinfo()`, and then use the result of the address lookup when
creating the socket, so it has the correct address family.

This allows both IPv4 and IPv6 to work, because the socket is created with
the correct AF_INETx type for the address.

Also add some more comments to the examples to explain what's going on.

Fixes issue #15580.
Signed-off-by: Damien George <damien@micropython.org>

Currently, the qemu-arm (and qemu-riscv) port has two build modes:
- a simple test that executes a Python string; and
- a full test that uses tinytest to embed all tests within the firmware,
  then executes that and captures the output.

This is very different to all the other ports.  A difficulty with using
tinytest is that with the large number of tests the firmware overflows its
virtual flash size.  It's also hard to run tests via .mpy files and with
the native emitter.  Being different to the other ports also means an extra
burden on maintenance.

This commit reworks the qemu-arm port so that it has a single build target
that creates a standard firmware which has a REPL.  When run under
qemu-system-arm, the REPL acts like any other bare-metal port, complete
with soft reset (use machine.reset() to turn it off and exit
qemu-system-arm).

This approach gives many benefits:
- allows playing with a REPL without hardware;
- allows running the test suite as it would on a bare-metal board, by
  making qemu-system-arm redirect the UART serial of the virtual device to
  a /dev/pts/xx file, and then running run-tests.py against that serial
  device;
- skipping tests is now done via the logic in `run-tests.py` and no longer
  needs multiple places to define which tests to skip
  (`tools/tinytest-codegen.py`, `ports/qemu-arm/tests_profile.txt` and also
  `tests/run-tests.py`);
- allows testing/using mpremote with the qemu-arm port.

Eventually the qemu-riscv port would have a similar change.

Prior to this commit the test results were:

    743 tests ok.  (121 skipped)

With this commit the test results are:

    753 tests performed (22673 individual testcases)
    753 tests passed
    138 tests skipped

More tests are skipped because more are included in the run. But overall
more tests pass.
Signed-off-by: Damien George <damien@micropython.org>

Signed-off-by: Damien George <damien@micropython.org>

So multiple boards can be built at once.
Signed-off-by: Damien George <damien@micropython.org>

Signed-off-by: Damien George <damien@micropython.org>

Signed-off-by: Damien George <damien@micropython.org>

Signed-off-by: Damien George <damien@micropython.org>