GitLab

Enabling the following features for all targets, except for nrf51
targets compiled to be used with SoftDevice:

- MICROPY_PY_ARRAY_SLICE_ASSIGN
- MICROPY_PY_SYS_STDFILES
- MICROPY_PY_UBINASCII

Splitting mpconfigport.h into multiple device specific
files in order to facilitate variations between devices.

Due to the fact that the devices might have variations in
features and also variations in flash size it makes sense
that some devices offers more functionality than others
without being limited by restricted devices.

For example more micropython features can be activated for
nrf52840 with 1MB flash, compared to nrf51 with 256KB.

Fixing 98e58343, the semantics of strncpy
require that the remainder of dst be filled with null bytes.
Signed-off-by: Damien George <damien@micropython.org>

This code is imported from musl, to match existing code in libm_dbl.

The file is also added to the build in stm32/Makefile.  It's not needed by
the core code but, similar to c5cc6417,
allows round() to be used by user C modules or board extensions.

Because the argument arrays may overlap, as show by the new tests in this
commit.

Also remove the debugging comments for these macros, add a new comment
about overlapping regions, and separate the macros by blank lines to make
them easier to read.

Fixes issue #6244.
Signed-off-by: Damien George <damien@micropython.org>

Signed-off-by: Damien George <damien@micropython.org>

Changes in this new library version are:
- Update H7 HAL to v1.6.0.
- Update WB HAL to v1.6.0.
- Add patches to fix F4 ll_uart clock selection for UART9/UART10.
Signed-off-by: Damien George <damien@micropython.org>

Signed-off-by: Kenneth Ryerson <kenneth.ryerson@gmail.com>

This explains how looping now works, and removes the warning about calling
wait_done().

A previous commit 3a9d9480 can cause
lock-ups of the RMT driver, so this commit reverses that, adds a loop_en
flag, and explicitly controls the TX interrupt in write_pulses().  This
provides correct looping, non-blocking writes and sensible behaviour for
wait_done().

See also #6167.

The stm32 and esp32 ports now use shorter error strings for mbedtls errors.
Also, MBEDTLS_ERROR_C is enabled on stm32 by default to get these strings.

The file `mbedtls_errors/mp_mbedtls_errors.c` can be used instead of
`mbedtls/library/error.c` to give shorter error strings, reducing the build
size of the error strings from about 12-16kB down to about 2-5kB.

This commit adds human readable error messages when mbedtls or axtls raise
an exception.  Currently often just an EIO error is raised so the user is
lost and can't tell whether it's a cert error, buffer overrun, connecting
to a non-ssl port, etc.  The axtls and mbedtls error raising in the ussl
module is modified to raise:

    OSError(-err_num, "error string")

For axtls a small error table of strings is added and used for the second
argument of the OSErrer.  For mbedtls the code uses mbedtls' built-in
strerror function, and if there is an out of memory condition it just
produces OSError(-err_num).  Producing the error string for mbedtls is
conditional on them being included in the mbedtls build, via
MBEDTLS_ERROR_C.

This commit adds the IRQ_GATTS_INDICATE_DONE BLE event which will be raised
with the status of gatts_indicate (unlike notify, indications require
acknowledgement).

An example of its use is added to ble_temperature.py, and to the multitests
in ble_characteristic.py.

Implemented for btstack and nimble bindings, tested in both directions
between unix/btstack and pybd/nimble.

Also clarify behavior of `gatts_notify` and add some TODOs about adding an
event for indication acknowledgement.

The goal of this commit is to allow using ble.gatts_notify() at any time,
even if the stack is not ready to send the notification right now.  It also
addresses the same issue for ble.gatts_indicate() and ble.gattc_write()
(without response).  In addition this commit fixes the case where the
buffer passed to write-with-response wasn't copied, meaning it could be
modified by the caller, affecting the in-progress write.

The changes are:

- gatts_notify/indicate will now run in the background if the ACL buffer is
  currently full, meaning that notify/indicate can be called at any time.

- gattc_write(mode=0) (no response) will now allow for one outstanding
  write.

- gattc_write(mode=1) (with response) will now copy the buffer so that it
  can't be modified by the caller while the write is in progress.

All four paths also now track the buffer while the operation is in
progress, which prevents the GC free'ing the buffer while it's still
needed.

This mutex is used to make the unix port behave more like bare metal, i.e.
it allows "IRQ handlers" to run exclusively by making the mutex recursive.

It might compile fine with S132 as SoftDevice for nRF52840.
However, there might be different hardware on the SoC which in
turn could make it fail.

SoftDevice S140 is correct BLE stack for nRF52840 SoC and would
provide a more accurate test build.

Update toolchain to GNU Arm Embedded Toolchain.

Resolves dependencies for MICROPY_PY_TIME_TICKS which
requires to link against nrfx_rtc.c functions by setting
MICROPY_PY_MACHINE_RTCOUNTER to 1.

nRF9160 does not have any RTC2. Disable the configuration in
case of NRF9160_XXAA.

Example make command:

make BOARD=actinius_icarus

In case of error, NimBLE calls the read callback with attr = NULL.

Following the documented pyb can_send behavior in pyb.CAN docs.

So that micropython-dev can be used to test VFS code, and inspect and build
filesystem images that are compatible with bare-metal systems.
Signed-off-by: Damien George <damien@micropython.org>

Having time.ticks_ms/us/add/diff is very useful and used by many drivers,
libraries and components.

This commit adds time.ticks_ms/us support using RTC1 as the timebase.  It
also adds the time.ticks_add/diff helper functions.  This feature can be
enabled using MICROPY_PY_TIME_TICKS.  If disabled the system uses the
legacy sleep methods and does not have any ticks functions.

In addition support for MICROPY_EVENT_POLL_HOOK was added to the
time.sleep_ms(x) function, making this function more power efficient and
allows support for select.poll/asyncio.  To support this, the RTC's CCR0
was used to schedule a ~1msec event to wakeup the CPU.

Some important notes about the RTC timebase:

- Since the granularity of RTC1's ticks are approx 30usec, time.ticks_us is
not perfect, does not have 1us resolution, but is otherwise quite usable.
For tighter measurments the ticker's 1MHz counter should be used.

- time.ticks_ms(x) should *not* be called in an IRQ with higher prio than
the RTC overflow irq (3).  If so it introduces a race condition and
possibly leads to wrong tick calculations.

See #6171 and #6202.

When compiling for debug (-O0) the .text segment cannot fit the flash
region when MICROPY_ROM_TEXT_COMPRESSION=1, because the compiler does not
optimise away the large if-else chain used to select the correct compressed
string.

This commit enforces MICROPY_ROM_TEXT_COMPRESSION=0 when compiling for
debug (DEBUG=1).

Changing line ending character of cooked strings makes rshell/pyboard.py
work correctly over Bluetooth socat/pts devices.