stm32/boards/LEGO_HUB_NO6: Skip first 1MiB of SPI flash for storage.

The first 1MiB is used by the built-in bootloader and is best left as-is.
Signed-off-by: Damien George <damien@micropython.org>

ports/stm32/boards/LEGO_HUB_NO6/mpconfigboard.h

@@ -10,7 +10,7 @@
 #define MICROPY_HW_MCU_NAME                      "STM32F413"
 
 #define MICROPY_HW_HAS_SWITCH                    (0)
-#define MICROPY_HW_HAS_FLASH                     (0)
+#define MICROPY_HW_HAS_FLASH                     (1)
 #define MICROPY_PY_PYB_LEGACY                    (0)
 #define MICROPY_HW_ENTER_BOOTLOADER_VIA_RESET    (0)
 #define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
@@ -78,8 +78,12 @@
 #define MICROPY_HW_BLE_BTSTACK_CHIPSET_INSTANCE  btstack_chipset_cc256x_instance()
 
 // SPI flash, for R/W storage
+// The first 1MiB is skipped because it's used by the built-in bootloader
+#define MICROPY_HW_SPIFLASH_OFFSET_BYTES         (1024 * 1024)
+#define MICROPY_HW_SPIFLASH_BLOCKMAP(bl)         ((bl) + MICROPY_HW_SPIFLASH_OFFSET_BYTES / FLASH_BLOCK_SIZE)
+#define MICROPY_HW_SPIFLASH_BLOCKMAP_EXT(bl)     ((bl) + MICROPY_HW_SPIFLASH_OFFSET_BYTES / MP_SPIFLASH_ERASE_BLOCK_SIZE)
 #define MICROPY_HW_SPIFLASH_ENABLE_CACHE         (1)
-#define MICROPY_HW_SPIFLASH_SIZE_BITS            (256 * 1024 * 1024)
+#define MICROPY_HW_SPIFLASH_SIZE_BITS            (256 * 1024 * 1024 - MICROPY_HW_SPIFLASH_OFFSET_BYTES * 8)
 #define MICROPY_HW_SPIFLASH_CS                   (MICROPY_HW_SPI2_NSS)
 #define MICROPY_HW_SPIFLASH_SCK                  (MICROPY_HW_SPI2_SCK)
 #define MICROPY_HW_SPIFLASH_MISO                 (MICROPY_HW_SPI2_MISO)
@@ -89,15 +93,25 @@
 extern int32_t board_bdev_ioctl(void);
 extern struct _spi_bdev_t spi_bdev;
 #define MICROPY_HW_BDEV_IOCTL(op, arg) ( \
-    (op) == BDEV_IOCTL_NUM_BLOCKS ? (MICROPY_HW_SPIFLASH_SIZE_BITS / 8 / FLASH_BLOCK_SIZE - 1) : \
+    (op) == BDEV_IOCTL_NUM_BLOCKS ? (MICROPY_HW_SPIFLASH_SIZE_BITS / 8 / FLASH_BLOCK_SIZE) : \
     (op) == BDEV_IOCTL_INIT ? board_bdev_ioctl() : \
     spi_bdev_ioctl(&spi_bdev, (op), (arg)) \
     )
 
-// Jump over first block (bl + 1) as it is cleared by bootloader
-#define MICROPY_HW_BDEV_READBLOCKS(dest, bl, n) spi_bdev_readblocks(&spi_bdev, (dest), (bl + 1), (n))
-#define MICROPY_HW_BDEV_WRITEBLOCKS(src, bl, n) spi_bdev_writeblocks(&spi_bdev, (src), (bl + 1), (n))
-#define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev) // for extended block protocol
+// Configuration for stardard block protocol (block size FLASH_BLOCK_SIZE).
+#define MICROPY_HW_BDEV_READBLOCKS(dest, bl, n) \
+    spi_bdev_readblocks(&spi_bdev, (dest), MICROPY_HW_SPIFLASH_BLOCKMAP(bl), (n))
+#define MICROPY_HW_BDEV_WRITEBLOCKS(src, bl, n) \
+    spi_bdev_writeblocks(&spi_bdev, (src), MICROPY_HW_SPIFLASH_BLOCKMAP(bl), (n))
+
+// Configuration for extended block protocol (block size MP_SPIFLASH_ERASE_BLOCK_SIZE).
+#define MICROPY_HW_BDEV_BLOCKSIZE_EXT (MP_SPIFLASH_ERASE_BLOCK_SIZE)
+#define MICROPY_HW_BDEV_READBLOCKS_EXT(dest, bl, off, len) \
+    (spi_bdev_readblocks_raw(&spi_bdev, (dest), MICROPY_HW_SPIFLASH_BLOCKMAP_EXT(bl), (off), (len)))
+#define MICROPY_HW_BDEV_WRITEBLOCKS_EXT(src, bl, off, len) \
+    (spi_bdev_writeblocks_raw(&spi_bdev, (src), MICROPY_HW_SPIFLASH_BLOCKMAP_EXT(bl), (off), (len)))
+#define MICROPY_HW_BDEV_ERASEBLOCKS_EXT(bl, len) \
+    (spi_bdev_eraseblocks_raw(&spi_bdev, MICROPY_HW_SPIFLASH_BLOCKMAP_EXT(bl), (len)))
 
 // Board control config
 #define MICROPY_BOARD_STARTUP                    board_init