Skip to content

GitLab

M
micropython
Commit 805c7501 authored by iabdalkader's avatar iabdalkader Committed by Damien George
Browse files
Options

mimxrt/mimxrt_sdram: Allow boards to override the default SDRAM config. 

Signed-off-by: default avatariabdalkader <i.abdalkader@gmail.com>
parent 4b9c4591
Hide whitespace changes
Inline Side-by-side
Showing with 66 additions and 49 deletions
ports/mimxrt/mimxrt_sdram.c
View file @ 805c7501
......@@ -42,10 +42,51 @@ extern uint8_t __sdram_start;
#define SDRAM_PIN_CONFIG (0xE1UL)
#endif
void mimxrt_sdram_init(void) {
#ifndef MICROPY_HW_SDRAM_TIMING_TRC
#if defined(MIMXRT117x_SERIES)
#define MICROPY_HW_SDRAM_TIMING_TRC (60)
#define MICROPY_HW_SDRAM_TIMING_TRP (15)
#define MICROPY_HW_SDRAM_TIMING_TRCD (15)
#define MICROPY_HW_SDRAM_TIMING_TWR (2)
#define MICROPY_HW_SDRAM_TIMING_TRRD (2)
#define MICROPY_HW_SDRAM_TIMING_TXSR (70)
#define MICROPY_HW_SDRAM_TIMING_TRAS (42)
#define MICROPY_HW_SDRAM_TIMING_TREF (64 * 1000000 / 8192) // 64ms/8192
#define MICROPY_HW_SDRAM_CAS_LATENCY (kSEMC_LatencyThree)
#define MICROPY_HW_SDRAM_MEM_BUS_WIDTH (kSEMC_PortSize32Bit)
#define MICROPY_HW_SDRAM_COLUMN_BITS_NUM (kSEMC_SdramColunm_9bit)
#define MICROPY_HW_SDRAM_BURST_LENGTH (kSEMC_Sdram_BurstLen8)
#define MICROPY_HW_SDRAM_RBURST_LENGTH (1)
#define MICROPY_HW_SDRAM_DELAY_CHAIN (2)
#else
#define MICROPY_HW_SDRAM_TIMING_TRC (60)
#define MICROPY_HW_SDRAM_TIMING_TRP (18)
#define MICROPY_HW_SDRAM_TIMING_TRCD (18)
#define MICROPY_HW_SDRAM_TIMING_TWR (12)
#define MICROPY_HW_SDRAM_TIMING_TRRD (60)
#define MICROPY_HW_SDRAM_TIMING_TXSR (67)
#define MICROPY_HW_SDRAM_TIMING_TRAS (42)
#define MICROPY_HW_SDRAM_TIMING_TREF (64 * 1000000 / 8192) // 64ms/8192
#define MICROPY_HW_SDRAM_CAS_LATENCY (kSEMC_LatencyThree)
#define MICROPY_HW_SDRAM_MEM_BUS_WIDTH (kSEMC_PortSize16Bit)
#define MICROPY_HW_SDRAM_COLUMN_BITS_NUM (kSEMC_SdramColunm_9bit)
#define MICROPY_HW_SDRAM_BURST_LENGTH (kSEMC_Sdram_BurstLen1)
#define MICROPY_HW_SDRAM_RBURST_LENGTH (1)
#endif
#endif
#if !defined(MIMXRT117x_SERIES)
void mimxrt_sdram_init(void) {
// Set Clocks
#if defined(MIMXRT117x_SERIES)
CLOCK_InitPfd(kCLOCK_PllSys2, kCLOCK_Pfd1, 29);
clock_root_config_t rootCfg = { 0 };
rootCfg.mux = kCLOCK_SEMC_ClockRoot_MuxSysPll2Pfd1;
rootCfg.div = 2;
CLOCK_SetRootClock(kCLOCK_Root_Semc, &rootCfg);
#else
CLOCK_InitSysPfd(kCLOCK_Pfd2, 29); // '29' PLL2 PFD2 frequency = 528MHz * 18 / 29 = 327.72MHz (with 528MHz = PLL2 frequency)
CLOCK_SetMux(kCLOCK_SemcAltMux, 0); // '0' PLL2 PFD2 will be selected as alternative clock for SEMC root clock
CLOCK_SetMux(kCLOCK_SemcMux, 1); // '1' SEMC alternative clock will be used as SEMC clock root
......@@ -137,7 +178,7 @@ void mimxrt_sdram_init(void) {
IOMUXC_SetPinMux(MIMXRT_IOMUXC_SEMC_DQS, 1UL);
IOMUXC_SetPinConfig(MIMXRT_IOMUXC_SEMC_DQS, SDRAM_PIN_CONFIG);
#if defined(MIMXRT117x_SERIES)
#if defined(MIMXRT_IOMUXC_SEMC_DATA16)
// Data Pins 16..31
IOMUXC_SetPinMux(MIMXRT_IOMUXC_SEMC_DATA16, 0UL);
IOMUXC_SetPinConfig(MIMXRT_IOMUXC_SEMC_DATA16, SDRAM_PIN_CONFIG);
......@@ -209,62 +250,38 @@ void mimxrt_sdram_init(void) {
SEMC_Init(SEMC, &semc_cfg);
#if defined(MIMXRT117x_SERIES)
uint32_t clock_freq = CLOCK_GetRootClockFreq(kCLOCK_Root_Semc);
semc_sdram_config_t sdram_cfg = {
.csxPinMux = kSEMC_MUXCSX0,
.address = 0x80000000,
.memsize_kbytes = (MICROPY_HW_SDRAM_SIZE >> 10),
.portSize = kSEMC_PortSize32Bit, // two 16-bit SDRAMs make up 32-bit portsize
.burstLen = kSEMC_Sdram_BurstLen8,
.columnAddrBitNum = kSEMC_SdramColunm_9bit,
.casLatency = kSEMC_LatencyThree,
.tPrecharge2Act_Ns = 15, // tRP 15ns
.tAct2ReadWrite_Ns = 15, // tRCD 15ns
.tRefreshRecovery_Ns = 70, // Use the maximum of the (Trfc , Txsr).
.tWriteRecovery_Ns = 2, // tWR 2ns
.tCkeOff_Ns = 42, // The minimum cycle of SDRAM CLK off state. CKE is off in self refresh at a minimum period tRAS.
.tAct2Prechage_Ns = 40, // tRAS 40ns
.tSelfRefRecovery_Ns = 70,
.tRefresh2Refresh_Ns = 60,
.tAct2Act_Ns = 2, // tRC/tRDD 2ns
.tPrescalePeriod_Ns = 160 * (1000000000 / clock_freq),
.refreshPeriod_nsPerRow = 64 * 1000000 / 8192, // 64ms/8192
.refreshUrgThreshold = sdram_cfg.refreshPeriod_nsPerRow,
.refreshBurstLen = 1,
.delayChain = 2,
};
#else
uint32_t clock_freq = CLOCK_GetFreq(kCLOCK_SemcClk);
#endif
semc_sdram_config_t sdram_cfg = {
.csxPinMux = kSEMC_MUXCSX0,
.address = ((uint32_t)&__sdram_start),
.memsize_kbytes = (MICROPY_HW_SDRAM_SIZE >> 10), // Right shift by 10 == division by 1024
.portSize = kSEMC_PortSize16Bit,
.burstLen = kSEMC_Sdram_BurstLen1,
.columnAddrBitNum = kSEMC_SdramColunm_9bit,
.casLatency = kSEMC_LatencyThree,
.tPrecharge2Act_Ns = 18, // Trp 18ns
.tAct2ReadWrite_Ns = 18, // Trcd 18ns
.tRefreshRecovery_Ns = (60 + 67),
.tWriteRecovery_Ns = 12, // 12ns
.tCkeOff_Ns = 42, // The minimum cycle of SDRAM CLK off state. CKE is off in self refresh at a minimum period tRAS.
.tAct2Prechage_Ns = 42, // Tras 42ns
.tSelfRefRecovery_Ns = 67,
.tRefresh2Refresh_Ns = 60,
.tAct2Act_Ns = 60,
.tPrescalePeriod_Ns = 160 * (1000000000 / clock_freq),
.portSize = MICROPY_HW_SDRAM_MEM_BUS_WIDTH,
.burstLen = MICROPY_HW_SDRAM_BURST_LENGTH,
.columnAddrBitNum = MICROPY_HW_SDRAM_COLUMN_BITS_NUM,
.casLatency = MICROPY_HW_SDRAM_CAS_LATENCY,
.tPrecharge2Act_Ns = MICROPY_HW_SDRAM_TIMING_TRP,
.tAct2ReadWrite_Ns = MICROPY_HW_SDRAM_TIMING_TRCD,
.tRefreshRecovery_Ns = MICROPY_HW_SDRAM_TIMING_TXSR,
.tSelfRefRecovery_Ns = MICROPY_HW_SDRAM_TIMING_TXSR,
.tWriteRecovery_Ns = MICROPY_HW_SDRAM_TIMING_TWR,
.tCkeOff_Ns = MICROPY_HW_SDRAM_TIMING_TRAS,
.tAct2Prechage_Ns = MICROPY_HW_SDRAM_TIMING_TRAS,
.tRefresh2Refresh_Ns = MICROPY_HW_SDRAM_TIMING_TRC,
.tAct2Act_Ns = MICROPY_HW_SDRAM_TIMING_TRRD,
.tIdleTimeout_Ns = 0UL,
.refreshPeriod_nsPerRow = 64 * 1000000 / 8192, // 64ms/8192
.refreshUrgThreshold = 64 * 1000000 / 8192, // 64ms/8192
.refreshBurstLen = 1
.refreshPeriod_nsPerRow = MICROPY_HW_SDRAM_TIMING_TREF,
.refreshUrgThreshold = MICROPY_HW_SDRAM_TIMING_TREF,
.refreshBurstLen = MICROPY_HW_SDRAM_RBURST_LENGTH,
#ifdef MICROPY_HW_SDRAM_DELAY_CHAIN
.delayChain = MICROPY_HW_SDRAM_DELAY_CHAIN,
#endif
.tPrescalePeriod_Ns = 160 * (1000000000 / clock_freq),
};
#endif
(status_t)SEMC_ConfigureSDRAM(SEMC, kSEMC_SDRAM_CS0, &sdram_cfg, clock_freq);
}
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment