GitLab

Allows the Pico to behave as an SPI slave and allows apps to respond
with appropriate data through callbacks.

Fixes #1680

It would be possible for an IRQ-driven SPI user to fire
while the main app's SPI.beginTransaction was in process.
This would result in incorrect state for the main app since
the IRQ may overwrite some settings that the app already
set.

Disable all IRQs around the begin and end processes to avoid
the possibility.

Fixes #1147

When SPI.beginTransaction() is called, disable all GPIO IRQs that were
registered using SPI.usingInterrupt().  On SPI.endTransaction(), restore
all the IRQs to their prior state.

When built for the PicoW but run on a Pico (non-W), fall through to use
the wired Ethernet mutex instead of no mutex at all for LWIP protection.

Enable use of wired Ethernet modules as first-class LWIP citizens.  All
networking classes like MDNS, WebServer, HTTPClient, WiFiClient, and OTA
can use a wired Ethernet adapter just like built-in WiFi.

Two examples updated to show proper use.

Uses the Async Context support built into the Pico SDK.  When running on the
Pico  it will use the CYW43 async instance.

Uses modified wired Ethernet drivers, thanks Nicholas Humfrey!

Note, the classic, non-LWIP integrated `Ethernet` and related libraries
should still work fine (but not be able to use WebServer/HTTPS/etc.)

Fixes #775

Fix #1681 due to breakage of GDB 12.3 in Platform.IO
Remove new Binutils linker warning

isPicoW was missing the rp2040. qualifier.

Fixes #1696

Additional pin definitions for Pimoroni Tiny 2040, including using the Green LED element of the RGB LED as the default LED.

There are only 12 external header pins for GPIO, including 4 ADC pins, so there are less options for assigning pins than on a generic Pico RP2040. In particular, there can only be one SPI, and it can't have an SS pin but I've defined GPIO17, as on the pico, because the definition is used in generic / common.h.

BOOTSEL on the Pimoroni Tiny 2040 is connected to GPIO23. I don't know if that has any consequences for implementing reading from BOOTSEL for this board. That may need to be revisited, but it doesn't appear to involve any changes to pins_arduino.h.

Move to a patched ArduinoCore-API revision.

Fixes #1691

No functional changes, just for completeness.

For some reason `program ... reset" causes OpenOCD to leave the chip in a
state where the 2nd core does not come up properly, leading to problems in
FreeRTOS and others.

Use a separate reset sequence after programming to work around the issue.

Fixes #1687

Fixes #1682

Make the HID report wait up to 500ms for an existing one to go out
before giving up sending a report.

Fixes #1683

Fixes #1066

Implements a simple TDM mode for the I2S output object.

Fixes #1676

Fixes #1604.  Supports 2MB and 8MB revs

Major toolchain update including:
* GCC 12.3
* GDB 12
* OpenOCD 0.12
* Picotool 1.1.2

* Fix MDNS infinite recursion

* Remove legacy Picoprobe

Fixes #1313
Fixes #1650

Fixes  #1656

Setting a pin to the current value is a no-op, not fatal.

Fixes #1652

fixed typo in license.rst

Fixes #1619

Requiring the auto-discovery tool and serial monitor if they have not already been included by other boards (namely if AVR cores have been uninstalled in the IDE).

If another packet comes in between freeing `_rx_buf` and setting `_rx_buf` to 0, that new packet could get put into the same memory address and get concatenated to itself, which leads to an infinite loop.
New solution assigns a temp pointer, sets `rx_buf` to 0, then frees the memory, which guarantees `_rx_buf` always points to valid data.

Fixes #1620