GitLab

* Working example for HTTPS over Eduroam network

* Update WiFiClientSecureEnterprise.ino

Added Olimex board ESP32-PoE. pins_arduino header file based on the ESP32-EVB with changed SS pin and removed BOARD_HAS_1BIT_SDMMC macro.

* updated WifiClientEnterprise example

* Update WiFiClientEnterprise.ino

* Create pins_arduino.h

* Update boards.txt

Pycom LoPy + LoPy4 boards added

* Create pins_arduino.h

* Update pins_arduino.h

bugfix antenna switch GPIO port 16 -> 21

* Update pins_arduino.h

* Update pins_arduino.h

* Update pins_arduino.h

* Update pins_arduino.h

* Update pins_arduino.h

* Update boards.txt

* Updated table of tested locations

* updated

* Added HTTPUpdate class for downloading sketches from a server

* Added HTTPUpdate class for downloading sketches from a server

* Added HTTPUpdate to CMakeLists.txt

* Change ESP8266 class references to ESP32 for httpUpdate.ino example

* Change ESP8266 class references to ESP32 for httpUpdate.ino example. setLedPin() commented out because not all boards support LED_BUITLIN

* Added check to handle mixup of old and present api properly

* Correct HTTPClient::setTimeout() to convert milliseconds to seconds. Correct WiFiClient::setTimeout() to call Stream::setTimeout() with seconds converted back to milliseconds. Remove inproper checks for _insecure.

* Added small comment because it looked like the Travis build did not finish

* Pass client parameter into two new begin() functions. Set other begin() functions deprecated. Updated library version to 1.2

* Added working HTTPS example on a public url with a certificate

* Remove two unnecessary tests in ::disconnect()

* Add a scoping block to BasicHttpsClient.ino to assure HTTPClient is destroyed before WiFiClientSecure

* Added check to handle mixup of old and present api properly

* Correct HTTPClient::setTimeout() to convert milliseconds to seconds. Correct WiFiClient::setTimeout() to call Stream::setTimeout() with seconds converted back to milliseconds. Remove inproper checks for _insecure.

* Added small comment because it looked like the Travis build did not finish

* Added baudrate detection to esp32-hal-uart and HardwareSerial

* Solved compiler warning for uartResizeRxBuffer()

* Add unit to header variable name (timeout_ms)

* Reverting accidentally changed files to master

* Add small delay after baudrate detection

Pin definitions T8/T9 & DAC1/DAC2 Back To Front (Issue #1831)

Pin definitions T8/T9 & DAC1/DAC2 Back To Front

* make WiFi.softAP() more robust

* WiFi.softAP() revert fallback to WIFI_AUTH_OPEN

fixes #1875

Incorrect values used, use the proper defines from header-files instead.

* removed uint8_t Wire.endTransmission(uint8_t sendStop)

Having both endTransmission(bool) and endTransmission(uint8_t) creates problems.
There is no need for endTransmission(uint8_t)
endTransmission(1) and endTransmission(0) works with endTransmission(bool).
Removing endTransmission(uint8_t) allows the ESP32 code to be compatible with
all the other Arduino cores by allowing endTransmission(1) and endTranmission(0)
to work as it does on all the other cores.

* Wire library version bump for endTransmission() update

#1869 exposed a resource exhaustion issue. The current HAL layer for I2C support is designed to use a shared interrupt, But, during debugging to solve the interrupt overloading condition identified in #1588, and the generation of pr #1717, the interrupt allocation parameters were changed.  This change was unnecessary, the code will work successfully with shared interrupts.  So, there is no need to assign a private interrupt for each I2C peripheral.

* TX Flow Control and Code cleanup

* Use semaphore instead of delay

TX functionality is done.

* Use single buffer and empty queue on exit

* Fix compile issues because of LwIP code relocation

* Add temporary header to fix Azure not compiling

* Fix AsyncUDP early init

* AsyncUDP Multicast fixes

* Add source mac address and rework multicast

* Allow redefinition of default pins for Serials 1 and 2

* Update IDF to 3276a13

* Update esptool.py to 2.5.0

* Fix sketches

* Fix log level in BluetoothSetial

* rmt driver initial version

* supporting conti mode plus interrupts

* using conitnous mode for sending more data

* working continous mode

* rmt driver cleanup after conti mode

* initial version of rmt driver

* adding a simple example

* adding channel and block locks

* modified of rmt interface for simpler/easier usage

* adding header sentinels, split interface to common and additional settings

* Fixes per code review + support for rx callback mode

* renamed internal structures and enums, fixed formatting

* cmake support for rmt

* refactored tx-conti interrupts to function to make it more readable

* added Tx and Rx examples

* added license headers

* minor updates per review

* used struct access, renamed defines, corrected diagram

* Initial

* Implementation

* Add to CMakelist.txt

* Add example

* Add IRAM_ATTR

* First commit of FFat library

* Fixed reboot loops if no fat present. Added CMakeLists

* Functionalize the partition checks

* Cleanup, especially in format

* Dont format if mounted.  More wording cleanup

* 16M ffat should only be on 16M board

* Fix some casting issues that trip up the compiler when building as ESP-IDF component

* Add BPI-BIT boards connfig

* Add BPI-BIT v1.3 boards

* Add wESP32 support

* Add default Ethernet config

Few testers let me know, they were unable with connection to Eduroam network under PEAP+MsCHAPv2 methods.
They were trying many modifications. Solution is very absurd. 
Change board to STA mode manually. 
One tester from Italy was able to connect to Eduroam network under TTLS + MsCHAPv2 with that sketch too!

Sketch was tested and worked almost for all testers with that problem.

fixes #1734

* Add delay into example to allow print before sleep

* Changed to Serial.flush()

see #1800

(removed quotes from last line, and fixed indentation, no text changes)