GitLab

- Testing with Arduino & RPi indicates delay needs to be increased
slightly before flushing tx_fifo
- Fix addresses in RPi transfer example, and add stopListening()

- Moved bcm2835.h and .c to RPi folder
- Changed includes and makefile to accommodate

Accidentally copied old RPi examples on last commit (code merge)

Prevent inclusion of BCM2835 driver for non-linux devices

Merged code to simplify everything
- #31 Timing of stopListening() adjusted slightly to further prevent
blank ack-payloads if powering down while using ack-payloads or
switching between modes

character fix

Per #27 update to match http://tmrh20.github.io docs

per req. from sergio m.

- add #define for _SPI
- add links to alternate SPI libs

Fix compile errors when trying to use any of the three libraries
together - should allow softspi and uartspi to play nicely with the std
SPI library now

- Revert SPI to default lib by default. Configure via RF24_config.h #24
- Corrected CRC status reporting per https://github.com/evorios by
checking AA register

- Added softSPI support for https://github.com/greiman/DigitalIO library
- Updated SPI_UART code to allow use at the same time as the SPI library

Uses the SPI_UART library at https://github.com/TMRh20/Sketches

Per a tip from Andrew A. this should be the final nail in the coffin of
issue #7

http://www.airspayce.com/mikem/bcm2835/bcm2835-1.37.tar.gz

- Merge with latest BCM2835 driver changes
- Should allow full support for RPi B+ but is untested

... not sure why the .h file was left out the first time...

http://www.airspayce.com/mikem/bcm2835/bcm2835-1.37.tar.gz

- Merge with latest BCM2835 driver changes
- Should allow full support for RPi B+ but is untested

Choose a standard pin layout for all the examples based on the pin connection table in the readme files.
Different pin layout in the example files could lead to not working examples.

 - Changes in the pin layout table to describe how to connect the NRF24L01 pins to different boards
 - Remove duplicate readme information in the RPi readme file and point to the default RPi/RF24/readme.md file.

Per a tip from Andrew A. this should be the final nail in the coffin of
issue #7

http://www.airspayce.com/mikem/bcm2835/bcm2835-1.37.tar.gz

- Merge with latest BCM2835 driver changes
- Should allow full support for RPi B+ but is untested

... not sure why the .h file was left out the first time...

http://www.airspayce.com/mikem/bcm2835/bcm2835-1.37.tar.gz

- Merge with latest BCM2835 driver changes
- Should allow full support for RPi B+ but is untested

Select a standard pin layout for the examples and update README files.

Choose a standard pin layout for all the examples based on the pin connection table in the readme files.
Different pin layout in the example files could lead to not working examples.

 - Changes in the pin layout table to describe how to connect the NRF24L01 pins to different boards
 - Remove duplicate readme information in the RPi readme file and point to the default RPi/RF24/readme.md file.

3-pin code enhancement by https://github.com/tong67

ATTiny example updated per https://github.com/tong67 and
https://github.com/Carminepz

All I can say is it compiled in IDE 1.5.7...

Fix "warning: binary constants are a GCC extension".

Change the binary constants to hex.

- Added delay to first call to available()
a: Only delays IF called after startListening AND called less than a
certain time after the last time it was called
- Corrected mistake on last commit where flush_rx was added back
inadvertently