Performance tweaks to address #9

- added delays to stop/start listening on RPi
- removed buffer flushes on start/stop listening for RPi
- added modified transfernbd function to BCM library - one has no
delays, also removed one delay period from both by waiting for RX data
- modified transfernb function to stop sending if RX fifo is full
- added delay to stoplistening for arduino etc. (actually seems to
improve performance)
- tests on-par with Arduino performance

RF24.cpp

@@ -533,7 +533,7 @@ void RF24::stopListening(void)
   flush_tx();
   flush_rx();
   write_register(CONFIG, ( read_register(CONFIG) ) & ~_BV(PRIM_RX) );
-
+  delayMicroseconds(130); //Found that adding this delay back actually increases response time
 }
 
 /****************************************************************************/
@@ -972,6 +972,7 @@ void RF24::enableAckPayload(void)
   //
 
   write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P1) | _BV(DPL_P0));
+  dynamic_payloads_enabled = true;
 }
 
 /****************************************************************************/

RPi/RF24/RF24.cpp

@@ -32,7 +32,6 @@ uint8_t RF24::read_register(uint8_t reg, uint8_t* buf, uint8_t len)
 		*ptx++ = NOP ; // Dummy operation, just for reading
 	}
   bcm2835_spi_transfernb( (char *) spi_txbuff, (char *) spi_rxbuff, size);
-  //bcm2835_spi_transfernb( (char *) spi_txbuff, (char *) buf, size);
 
 	status = *prx++; // status is 1st byte of receive buffer
 
@@ -42,19 +41,20 @@ uint8_t RF24::read_register(uint8_t reg, uint8_t* buf, uint8_t len)
 	}
 
   return status;
-}
+} 
 
 /****************************************************************************/
 uint8_t RF24::read_register(uint8_t reg)
 {
   uint8_t result;
+	
 	uint8_t * prx = spi_rxbuff;
 	uint8_t * ptx = spi_txbuff;
-
+	
 	*ptx++ = ( R_REGISTER | ( REGISTER_MASK & reg ) );
 	*ptx++ = NOP ; // Dummy operation, just for reading
 
-  bcm2835_spi_transfernb( (char *) spi_txbuff, (char *) spi_rxbuff, 2);
+  bcm2835_spi_transfernbd( (char *) spi_txbuff, (char *) spi_rxbuff, 2);
 
 	result = *++prx;   // result is 2nd byte of receive buffer
 
@@ -66,13 +66,14 @@ uint8_t RF24::read_register(uint8_t reg)
 uint8_t RF24::write_register(uint8_t reg, uint8_t value)
 {
   uint8_t status;
+	
 	uint8_t * prx = spi_rxbuff;
 	uint8_t * ptx = spi_txbuff;
 
 	*ptx++ = ( W_REGISTER | ( REGISTER_MASK & reg ) );
 	*ptx = value ;
 
-  bcm2835_spi_transfernb( (char *) spi_txbuff, (char *) spi_rxbuff, 2);
+  	bcm2835_spi_transfernbd( (char *) spi_txbuff, (char *) spi_rxbuff, 2);  
 
 	status = *prx++; // status is 1st byte of receive buffer
 
@@ -162,7 +163,7 @@ uint8_t RF24::read_payload(void* buf, uint8_t len)
 	// Size has been lost during while, re affect
 	size = data_len + blank_len + 1; // Add register value to transmit buffer
 
-	bcm2835_spi_transfernb( (char *) spi_txbuff, (char *) spi_rxbuff, size);
+	bcm2835_spi_transfernbd( (char *) spi_txbuff, (char *) spi_rxbuff, size);
 
 	// 1st byte is status
 	status = *prx++;
@@ -512,14 +513,14 @@ void RF24::startListening(void)
     write_register(RX_ADDR_P0, pipe0_reading_address,addr_width);	
   }
   // Flush buffers
-  flush_rx();
-  flush_tx();
+  //flush_rx();
+  //flush_tx();
 
   // Go!
   bcm2835_gpio_write(ce_pin, HIGH);
 
   // wait for the radio to come up (130us actually only needed)
-  //delayMicroseconds(130);
+  delayMicroseconds(130);
 }
 
 /****************************************************************************/
@@ -527,10 +528,10 @@ void RF24::startListening(void)
 void RF24::stopListening(void)
 {
   bcm2835_gpio_write(ce_pin, LOW);
-  flush_tx();
-  flush_rx();
-  write_register(CONFIG, ( read_register(CONFIG) ) & ~_BV(PRIM_RX) );
-
+  //flush_tx();
+  //flush_rx();
+  write_register(CONFIG, ( read_register(CONFIG) ) & ~_BV(PRIM_RX) );  
+  delayMicroseconds(130);
 }
 
 /****************************************************************************/
@@ -567,9 +568,9 @@ bool RF24::write( const void* buf, uint8_t len, const bool multicast ){
     // If this hangs, it ain't coming back, no sense in timing out
 	while( ! ( get_status()  & ( _BV(TX_DS) | _BV(MAX_RT) ))) { }
 
-
-	uint8_t status = write_register(STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) );
 	bcm2835_gpio_write(ce_pin, LOW);
+	uint8_t status = write_register(STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) );
+	
 
   //Max retries exceeded
   if( status & _BV(MAX_RT)){
@@ -731,7 +732,7 @@ uint8_t RF24::getDynamicPayloadSize(void)
   spi_txbuff[0] = R_RX_PL_WID;
   spi_rxbuff[1] = 0xff;
 
-  bcm2835_spi_transfernb( (char *) spi_txbuff, (char *) spi_rxbuff, 2);
+  bcm2835_spi_transfernbd( (char *) spi_txbuff, (char *) spi_rxbuff, 2);
 
   if(spi_rxbuff[1] > 32) { flush_rx(); return 0; }
 
@@ -750,7 +751,6 @@ bool RF24::available(void)
 bool RF24::available(uint8_t* pipe_num)
 {
     //Check the FIFO buffer to see if data is waitng to be read
-
   if (!( read_register(FIFO_STATUS) & _BV(RX_EMPTY) )){
 
 
@@ -946,7 +946,7 @@ void RF24::enableAckPayload(void)
   //
   // Enable dynamic payload on pipes 0 & 1
   //
-
+  dynamic_payloads_enabled = true;
   write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P1) | _BV(DPL_P0));
 }
 
@@ -985,7 +985,7 @@ void RF24::writeAckPayload(uint8_t pipe, const void* buf, uint8_t len)
   while ( data_len-- ){
     *ptx++ =  *current++;
   }
-	bcm2835_spi_transfern( (char *) spi_txbuff, size);
+	bcm2835_spi_transfernb( (char *) spi_txbuff,(char *)spi_rxbuff, size);
 
 }
 

RPi/RF24/bcm2835.c

@@ -562,17 +562,15 @@ uint8_t bcm2835_spi_transfer(uint8_t value)
 
     // Maybe wait for TXD
     while (!(bcm2835_peri_read(paddr) & BCM2835_SPI0_CS_TXD)){
-		delayMicroseconds(10);
+		
 	}
-
     // Write to FIFO, no barrier
     bcm2835_peri_write_nb(fifo, value);
 
     // Wait for DONE to be set
     while (!(bcm2835_peri_read_nb(paddr) & BCM2835_SPI0_CS_DONE)){
-		delayMicroseconds(10);
-	}
-
+		
+	}	
     // Read any byte that was sent back by the slave while we sere sending to it
     uint32_t ret = bcm2835_peri_read_nb(fifo);
 
@@ -586,8 +584,19 @@ uint8_t bcm2835_spi_transfer(uint8_t value)
     return ret;
 }
 
-// Writes (and reads) an number of bytes to SPI
 void bcm2835_spi_transfernb(char* tbuf, char* rbuf, uint32_t len)
+{
+	__bcm2835_spi_transfernb(tbuf,rbuf,len,0);
+}
+
+void bcm2835_spi_transfernbd(char* tbuf, char* rbuf, uint32_t len)
+{
+	__bcm2835_spi_transfernb(tbuf,rbuf,len,1);
+}
+
+
+// Writes (and reads) an number of bytes to SPI
+void __bcm2835_spi_transfernb(char* tbuf, char* rbuf, uint32_t len, uint8_t delay)
 {
     volatile uint32_t* paddr = bcm2835_spi0 + BCM2835_SPI0_CS/4;
     volatile uint32_t* fifo = bcm2835_spi0 + BCM2835_SPI0_FIFO/4;
@@ -608,28 +617,36 @@ void bcm2835_spi_transfernb(char* tbuf, char* rbuf, uint32_t len)
     while((TXCnt < len)||(RXCnt < len))
     {
         // TX fifo not full, so add some more bytes
-        while(((bcm2835_peri_read(paddr) & BCM2835_SPI0_CS_TXD))&&(TXCnt < len ))
+        while( (bcm2835_peri_read(paddr) & BCM2835_SPI0_CS_TXD )  && (TXCnt < len )  && !(bcm2835_peri_read(paddr) & BCM2835_SPI0_CS_RXR) )
         {
-		   delayMicroseconds(10);
            bcm2835_peri_write_nb(fifo, tbuf[TXCnt]);
            TXCnt++;
-        }
+        }	
         //Rx fifo not empty, so get the next received bytes
+	while(! (bcm2835_peri_read(paddr) & BCM2835_SPI0_CS_RXD) ){}
         while(((bcm2835_peri_read(paddr) & BCM2835_SPI0_CS_RXD))&&( RXCnt < len ))
         {
-		   delayMicroseconds(10);
+		   
            rbuf[RXCnt] = bcm2835_peri_read_nb(fifo);
            RXCnt++;
+	   
         }
+	if(delay){ delayMicroseconds(10); }
+
     }
+
     // Wait for DONE to be set
     while (!(bcm2835_peri_read_nb(paddr) & BCM2835_SPI0_CS_DONE)){
-		delayMicroseconds(10);
+		
 	}
+    
     // Set TA = 0, and also set the barrier
     bcm2835_peri_set_bits(paddr, 0, BCM2835_SPI0_CS_TA);
+    if(delay){delayMicroseconds(10);}
 }
 
+
+
 // Writes an number of bytes to SPI
 void bcm2835_spi_writenb(char* tbuf, uint32_t len)
 {

RPi/RF24/bcm2835.h

@@ -1177,6 +1177,8 @@ extern "C" {
     /// \param[in] len Number of bytes in the tbuf buffer, and the number of bytes to send/received
     /// \sa bcm2835_spi_transfer()
     extern void bcm2835_spi_transfernb(char* tbuf, char* rbuf, uint32_t len);
+    extern void bcm2835_spi_transfernbd(char* tbuf, char* rbuf, uint32_t len);
+    extern void __bcm2835_spi_transfernb(char* tbuf, char* rbuf, uint32_t len,uint8_t delay);
 
     /// Transfers any number of bytes to and from the currently selected SPI slave
     /// using bcm2835_spi_transfernb.