stm32/boards/LEGO_HUB_NO6: Change SPI flash storage to use hardware SPI.

Signed-off-by: Damien George <damien@micropython.org>

ports/stm32/boards/LEGO_HUB_NO6/bdev.c

@@ -26,25 +26,26 @@
 
 #include "py/obj.h"
 #include "storage.h"
+#include "spi.h"
 
 #define CMD_EXIT_4_BYTE_ADDRESS_MODE (0xE9)
 
-STATIC const mp_soft_spi_obj_t soft_spi_bus = {
-    .delay_half = MICROPY_HW_SOFTSPI_MIN_DELAY,
+STATIC const spi_proto_cfg_t spi_bus = {
+    .spi = &spi_obj[1], // SPI2 hardware peripheral
+    .baudrate = 25000000,
     .polarity = 0,
     .phase = 0,
-    .sck = MICROPY_HW_SPIFLASH_SCK,
-    .mosi = MICROPY_HW_SPIFLASH_MOSI,
-    .miso = MICROPY_HW_SPIFLASH_MISO,
+    .bits = 8,
+    .firstbit = SPI_FIRSTBIT_MSB,
 };
 
 STATIC mp_spiflash_cache_t spi_bdev_cache;
 
 const mp_spiflash_config_t spiflash_config = {
     .bus_kind = MP_SPIFLASH_BUS_SPI,
-    .bus.u_spi.cs = MICROPY_HW_SPIFLASH_NSS,
-    .bus.u_spi.data = (void *)&soft_spi_bus,
-    .bus.u_spi.proto = &mp_soft_spi_proto,
+    .bus.u_spi.cs = MICROPY_HW_SPIFLASH_CS,
+    .bus.u_spi.data = (void *)&spi_bus,
+    .bus.u_spi.proto = &spi_proto,
     .cache = &spi_bdev_cache,
 };
 
@@ -55,9 +56,9 @@ int32_t board_bdev_ioctl(void) {
 
     // Exit 4-byte address mode
     uint8_t cmd = CMD_EXIT_4_BYTE_ADDRESS_MODE;
-    mp_hal_pin_write(MICROPY_HW_SPIFLASH_NSS, 0);
-    mp_soft_spi_proto.transfer(MP_OBJ_FROM_PTR(&soft_spi_bus), 1, &cmd, NULL);
-    mp_hal_pin_write(MICROPY_HW_SPIFLASH_NSS, 1);
+    mp_hal_pin_write(MICROPY_HW_SPIFLASH_CS, 0);
+    spi_proto.transfer(MP_OBJ_FROM_PTR(&spi_bus), 1, &cmd, NULL);
+    mp_hal_pin_write(MICROPY_HW_SPIFLASH_CS, 1);
 
     return ret;
 }

ports/stm32/boards/LEGO_HUB_NO6/mpconfigboard.h

@@ -61,6 +61,10 @@
 #define MICROPY_HW_SPI1_SCK                      (pin_A5) // shared with DAC
 #define MICROPY_HW_SPI1_MISO                     (pin_A6)
 #define MICROPY_HW_SPI1_MOSI                     (pin_A7)
+#define MICROPY_HW_SPI2_NSS                      (pin_B12)
+#define MICROPY_HW_SPI2_SCK                      (pin_B13)
+#define MICROPY_HW_SPI2_MISO                     (pin_C2)
+#define MICROPY_HW_SPI2_MOSI                     (pin_C3)
 
 // USB config
 #define MICROPY_HW_USB_VBUS_DETECT_PIN           (pin_A9)
@@ -76,10 +80,10 @@
 // SPI flash, for R/W storage
 #define MICROPY_HW_SPIFLASH_ENABLE_CACHE         (1)
 #define MICROPY_HW_SPIFLASH_SIZE_BITS            (256 * 1024 * 1024)
-#define MICROPY_HW_SPIFLASH_NSS                  (pin_B12)
-#define MICROPY_HW_SPIFLASH_SCK                  (pin_B13)
-#define MICROPY_HW_SPIFLASH_MISO                 (pin_C2)
-#define MICROPY_HW_SPIFLASH_MOSI                 (pin_C3)
+#define MICROPY_HW_SPIFLASH_CS                   (MICROPY_HW_SPI2_NSS)
+#define MICROPY_HW_SPIFLASH_SCK                  (MICROPY_HW_SPI2_SCK)
+#define MICROPY_HW_SPIFLASH_MISO                 (MICROPY_HW_SPI2_MISO)
+#define MICROPY_HW_SPIFLASH_MOSI                 (MICROPY_HW_SPI2_MOSI)
 
 // SPI flash, block device config
 extern int32_t board_bdev_ioctl(void);