mailbox: control LED through the little core

freertos/cvitek/driver/rtos_cmdqu/include/rtos_cmdqu.h

@@ -9,14 +9,20 @@
 #define NR_RTOS_CMD            127
 #define NR_RTOS_IP        IP_LIMIT
 
-
 enum SYS_CMD_ID {
 	CMD_TEST_A	= 0x10,
 	CMD_TEST_B,
 	CMD_TEST_C,
+	CMD_DUO_LED,
 	SYS_CMD_INFO_LIMIT,
 };
 
+enum DUO_LED_STATUS {
+	DUO_LED_ON	= 0x02,
+	DUO_LED_OFF,
+	DUO_LED_DONE,
+};
+
 struct valid_t {
 	unsigned char linux_valid;
 	unsigned char rtos_valid;

freertos/cvitek/task/comm/src/riscv64/comm_main.c

@@ -18,6 +18,8 @@
 #include "comm.h"
 #include "cvi_spinlock.h"
 
+/* Milk-V Duo */
+#include "milkv_duo_io.h"
 
 // #define __DEBUG__
 #ifdef __DEBUG__
@@ -94,7 +96,6 @@ void main_cvirtos(void)
     /* Start the tasks and timer running. */
     vTaskStartScheduler();
 
-
     /* If all is well, the scheduler will now be running, and the following
     line will never be reached.  If the following line does execute, then
     there was either insufficient FreeRTOS heap memory available for the idle
@@ -158,6 +159,19 @@ void prvCmdQuRunTask(void *pvParameters)
 				rtos_cmdq.resv.valid.linux_valid = 0;
 				printf("recv cmd(%d) from C906B...send [0x%x] to C906B\n", rtos_cmdq.cmd_id, rtos_cmdq.param_ptr);
 				goto send_label;
+			case CMD_DUO_LED:
+				rtos_cmdq.cmd_id = CMD_DUO_LED;
+				printf("recv cmd(%d) from C906B, param_ptr [0x%x]\n", rtos_cmdq.cmd_id, rtos_cmdq.param_ptr);
+				if (rtos_cmdq.param_ptr == DUO_LED_ON) {
+					duo_led_control(1);
+				} else {
+					duo_led_control(0);
+				}
+				rtos_cmdq.param_ptr = DUO_LED_DONE;
+				rtos_cmdq.resv.valid.rtos_valid = 1;
+				rtos_cmdq.resv.valid.linux_valid = 0;
+				printf("recv cmd(%d) from C906B...send [0x%x] to C906B\n", rtos_cmdq.cmd_id, rtos_cmdq.param_ptr);
+				goto send_label;
 			default:
 send_label:
 				/* used to send command to linux*/

freertos/cvitek/task/comm/src/riscv64/milkv_duo_io.c

+#include "milkv_duo_io.h"
+
+void duo_led_control(int enable)
+{
+	*(uint32_t*)(GPIO2 | GPIO_SWPORTA_DDR) = 1 << 24;
+
+	if (enable) {
+		*(uint32_t*)(GPIO2 | GPIO_SWPORTA_DR) = 1 << 24;
+	} else {
+		*(uint32_t*)(GPIO2 | GPIO_SWPORTA_DR) = 0;
+	}
+}

freertos/cvitek/task/comm/src/riscv64/milkv_duo_io.h

+#include <stdio.h>
+/*
+ * The blue LED on Duo is GPIOC24.
+ * The datasheet page 536 says:
+ * Configure register GPIO_SWPORTA_DDR and set GPIO as input or output.
+ * When the output pin is configured, write the output value to the
+ * GPIO_SWPORTA_DR register to control the GPIO output level.
+ */
+
+#define GPIO2 0x03022000
+#define GPIO_SWPORTA_DR 0x000
+#define GPIO_SWPORTA_DDR 0x004
+
+void duo_led_control(int enable);

linux_5.10/drivers/soc/cvitek/rtos_cmdqu/Makefile

@@ -3,3 +3,4 @@ cvi_mbox-y := rtos_cmdqu.o \
 			cvi_spinlock.o
 
 ccflags-y += -I$(srctree)/$(src)/
+ccflags-$(CONFIG_DYNAMIC_DEBUG) += -DDEBUG

linux_5.10/drivers/soc/cvitek/rtos_cmdqu/rtos_cmdqu.h

@@ -33,13 +33,6 @@ enum SYSTEM_CMD_TYPE {
 	CMDQU_SYSTEM_LIMIT = NR_SYSTEM_CMD,
 };
 
-enum SYS_CMD_ID {
-	CMD_TEST_A	= 0x10,
-	CMD_TEST_B,
-	CMD_TEST_C,
-	SYS_CMD_INFO_LIMIT,
-};
-
 #define RTOS_CMDQU_DEV_NAME "cvi-rtos-cmdqu"
 #define RTOS_CMDQU_SEND                         _IOW('r', CMDQU_SEND, unsigned long)
 #define RTOS_CMDQU_SEND_WAIT                    _IOW('r', CMDQU_SEND_WAIT, unsigned long)